Qualitätsprüfung „Messung“¶
In Odoo Quality, a Measure check is one of the quality check types that can be selected when creating a new quality check or quality control point (QCP). Measure checks prompt users to measure a certain aspect of a product and record the measurement in Odoo. For the quality check to pass, the recorded measurement must be within a certain tolerance of a norm value.
Create a Measure quality check¶
There are two distinct ways that Measure quality checks can be created. A single check can be manually created. Alternatively, a QCP can be configured that automatically creates checks at a predetermined interval.
This documentation only details the configuration options that are unique to Measure quality checks and QCPs. For a full overview of all the configuration options available when creating a single check or a QCP, see the documentation on quality checks and quality control points.
Qualitätsprüfung¶
To create a single Measure quality check, navigate to , and click New. Fill out the new quality check form as follows:
In the Type drop-down field, select the Measure quality check type.
In the Team drop-down field, select the quality team responsible for managing the check.
In the Instructions text field of the Notes tab, enter instructions for how the picture should be taken.
Qualitätskontrollpunkt¶
To create a QCP that generates Measure quality checks automatically, navigate to , and click New. Fill out the new QCP form as follows:
In the Type drop-down field, select the Measure quality check type. Doing so causes two new fields to appear: Norm and Tolerance.
Use the first text-entry field of the Norm field to record the ideal measurement that the product should conform to. Use the second text-entry field to specify the unit of measurement that should be used.
The Tolerance field features two sub-fields: from and to. Use the from field to specify the minimum acceptable measurement, and the to field to specify the maximum acceptable measurement.
In the Team drop-down field, select the quality team responsible for managing the checks created by the QCP.
In the Instructions text field, enter instructions for how the measurement should be taken.
Qualitätsprüfung „Messung“ verarbeiten¶
Nach der Erstellung gibt es mehrere Möglichkeiten, wie Qualitätsprüfungen für Messung verarbeitet werden können. Wenn eine Qualitätsprüfung einem bestimmten Fertigungs-, Bestands- oder Arbeitsauftrag zugewiesen ist, kann die Prüfung auf dem Auftrag selbst verarbeitet werden. Alternativ kann eine Prüfung auch von der Seite der Prüfung aus bearbeitet werden.
Über die Seite der Prüfung¶
Um eine Qualitätsprüfung Messung von der Seite der Prüfungen aus zu bearbeiten, navigieren Sie zunächst zu Qualität –> Qualitätskontrolle –> Qualitätsprüfungen und wählen dann eine Qualitätsprüfung aus. Befolgen Sie die Messung zum Aufnehmen des Bilds.
Tragen Sie nach der Messung den Wert in das Feld Messung auf dem Qualitätsprüfungsformular ein. Um die Prüfung manuell als bestanden oder fehlgeschlagen zu bewerten, klicken Sie oben links auf der Prüfung auf Bestanden oder Fehlgeschlagen.
Alternativ können Sie, wenn die Qualitätsprüfung einem Qualitätskontrollpunkt zugewiesen ist, für das Norm- und Toleranz-Werte angegeben wurden, stattdessen auf Messung in der oberen linken Ecke der Prüfung klicken. Dadurch wird die Prüfung automatisch als Bestanden markiert, wenn der aufgezeichnete Wert innerhalb der angegebenen Toleranz liegt, oder als Fehlgeschlagen, wenn der Wert außerhalb der Toleranz liegt.
Auf einem Auftrag¶
Um eine Qualitätsprüfung Messung für einen Auftrag durchzuführen, wählen Sie einen Fertigungs- oder Lagerauftrag (Wareneingang, Lieferung, Retoure usw.), für den eine Prüfung erforderlich ist. Fertigungsaufträge können Sie auswählen, indem Sie zu navigieren und einen Auftrag anklicken. Lageraufträge können ausgewählt werden, indem Sie zu navigieren, auf einer Vorgangskarte auf die Schaltfläche # Zu verarbeiten klicken und einen Auftrag auswählen.
Auf dem ausgewählten Lager- oder Fertigungsauftrag erscheint eine violette Schaltfläche Qualitätsprüfungen am oberen Rand der Seite. Klicken Sie auf die Schaltfläche, um das Pop-up-Fenster Qualitätsprüfung zu öffnen, in dem alle für diesen Auftrag erforderlichen Qualitätsprüfungen angezeigt werden.
To process a Measure quality check, measure the product as instructed, then enter the value in the Measure field on the pop-up window. Finally, click Validate to register the recorded value.
If the value entered is within the range specified in the Tolerance section of the QCP, the quality check passes and the pop-up window closes. The rest of the manufacturing or inventory order can then be processed as usual.
However, if the value entered is outside of the specified range, a new pop-up window appears, titled Quality Check Failed. The body of the pop-up shows a warning message that states, You measured # units and it should be between # units and # units., as well as the instructions entered in the Message If Failure tab of the QCP. At the bottom of the pop-up, two buttons appear: Correct Measure and Confirm Measure.
If the measurement was not entered correctly and should be changed, select Correct Measure. Doing so re-opens the Quality Check pop-up window. Enter the corrected measurement in the Measure field, and then click Validate to complete the check.
If the measurement was entered correctly, click Confirm Measure instead, and the quality check fails. Follow any instructions that were listed on the Quality Check Failed pop-up window.
If a quality alert must be created, click the Quality Alert button that appears at the top of the manufacturing or inventory order after the check fails. Clicking Quality Alert opens a quality alert form on a new page.
Siehe auch
Eine vollständige Anleitung zum Ausfüllen des Qualitätsalarmformulars finden Sie in der Dokumentation zu Qualitätsalarmen.
Auf einem Arbeitsauftrsg¶
Bei der Konfiguration eines Qualitätskontrollpunkts, der während der Fertigung ausgelöst wird, kann im Feld Arbeitsauftragsvorgang des Formulars des Qualitätskontrollpunkts auch ein bestimmter Arbeitsauftrag angegeben werden. Wenn ein Arbeitsauftrag angegeben wird, wird eine Qualitätsprüfung mit dem Ergebnis Messung für diesen spezifischen Arbeitsauftrag erstellt und nicht für den Fertigungsauftrag als Ganzes.
Measure quality checks configured for work orders must be completed from the Shop Floor module. To do so, begin by navigating to . Select an MO that includes a work order for which a Measure quality check is required.
Klicken Sie auf dem Fertigungsauftrag auf den Reiter Arbeitsaufträge und klicken Sie dann auf die Schaltfläche Arbeitsauftrg öffnen (externer Link) in der Zeile des ersten zu bearbeitenden Arbeitsauftrags. Klicken Sie daraufhin im Pop-up-Fenster Arbeitsaufträge auf die Schaltfläche Werkstatt öffnen, um das Werkstatt-Modul zu öffnen.
Wenn Sie von einem bestimmten Arbeitsauftrag auf das Werkstatt-Modul zugreifen, wird standardmäßig die Seite für den Arbeitsplatz angezeigt, an dem der Auftrag ausgeführt werden soll und isoliert die Karte des Arbeitsauftrags, so dass keine anderen Karten angezeigt werden.
Process the work order’s steps until the Measure quality check step is reached. Click on the step to open a pop-up window that includes instructions for how the measurement should be taken. After taking the measurement, enter it in the Measure field of the pop-up window, and then click Validate.
If the measurement entered is within the range specified in the Tolerance section of the QCP, the quality check passes, and the pop-up window moves on to the next step of the work order. However, if the measurement entered is outside of the specified range, a new pop-up window appears, titled Quality Check Failed.
The body of the Quality Check Failed pop-up window shows a message that states, You measured # units and it should be between # units and # units, as well as the instructions entered in the Message If Failure tab of the QCP. At the bottom of the pop-up window, two buttons appear: Correct Measure and Confirm Measure.
If the measurement was not entered correctly, and should be changed, select Correct Measure. Doing so opens a new pop-up window, titled Quality Check. Enter the corrected measure in the Measure field, and then click Validate to complete the check and close the pop-up window.
If the measurement was entered correctly, click Confirm Measure instead, and the quality check fails. Follow any instructions that were listed on the Quality Check Failed pop-up window.
If a quality alert must be created, exit the pop-up window by clicking the X (close) button in the top-right corner.
Then, click the ⋮ (three vertical dots) button on the bottom-right corner of the work order card to open the What do you want to do? pop-up window.
On the What do you want to do? pop-up window, select the Create a Quality Alert button. Doing so opens a blank quality alert form in a new Quality Alerts pop-up window.
Siehe auch
Eine vollständige Anleitung zum Ausfüllen von Qualitätsalarmformularen finden Sie in der Dokumentation zu Qualitätsalarmen.